A2N Kernel Control for Galaxy Ace 2

ace2nutzer工具2019-06-25

價格：免費

更新日期：2019-06-25

檔案大小：83k

目前版本：6.6

版本需求：Android 4.1 - 8.0

官方網站：https://plus.google.com/u/0/+ace2nutzerA2N

Email：ace2nutzer@gmail.com

聯絡地址：Silvestro Sanfilippo Kronstädter Straße 17 50858 Köln

If you installed the powerful A2N Kernel to your Galaxy Ace 2 then this Kernel Control App is a "must-have-App" to enjoy your Phone and Kernel properly.

This App is only for the following Devices and only in combination with A2N Kernel.

### Supported Devices ###

--> GT-I8160

--> GT-I8160P

--> GT-I8160L

### App Features ###

# Power

--> Allows you to adjust AC / USB 2.0 Charging Current(max) (separately) from 100 - 1000 mA in 100 mA Steps (Fail-safe)

--> Charging Current - Check if the power source can handle the selected Current, if it's unstable the Kernel will reduce the Current till it is safe.

--> 80% Charge - Stops and holds charging at 80%, useful if charging over night to reduce the battery stress.

--> BLN EOC - When Battery is full turn on the Soft-Keys LEDs.

--> USB Power - Enables output Voltage to the USB Port, useful if u need to power up some usb gadgets (no real OTG Support)

--> Show power Menu - using an emulated power-button press, useful if the power-button is broken (You can boot the Phone with a cheap USB-JIG Adapter)

# Audio #

--> Low Level Gain Control - Headphones, Earpiece and Microphone

--> LPA - Low-Power-Audio, reduces Audio Voltage on Suspend for Powersaving (up to -100 mV)

--> Volume Control - Emulated buttons press (useful if the hardware buttons are broken)

# Screen #

--> Sweep2Wake - Wake up the phone with a Swipe

--> Suspend - Emulated (useful if the Power button is broken)

# CPU #

--> Adjust CPU Max Frequency - Overclock Control (400 - 1300 MHz)**1

--> Undervolting (up to -200 mV)

# GPU #

--> Adjust GPU Max Frequency - Overclock Control (450 - 800 MHz)**2

--> Undervolting (up to -200 mV)

# Performance Profile #

--> Powersave

--> Balanced

--> Performance

# Misc #

--> KSM - Kernel same page merging, to use RAM more efficient (only 1% CPU load on Idle)

--> Check shared RAM - Shows the amount of saved RAM in MB

--> FSB/DDR Overclock (overclocks FSB/DDR Frequency from 200/800 MHz to 250/1000 MHz, improves overall performance)

--> Torch Brightness - allows you to adjust the Brightness of the rear LED (Camera Flash for Torch)

--> Use as Notifications LED - uses the Soft-Key LEDs

--> ON/OFF Delay - Ability to adjust how the LEDs should blink

--> Network File Systems - Enables Support for CIFS and NFS

--> Use calibration data - Accelerometer calibration

--> Disable Logger - Disables Android Logger, for powersaving

# Debug-Menu #

--> Disable Restore on Reboot - Disable restoring of settings on reboot, useful if you are not sure whether the settings are stable.

Otherwise all settings will survive a reboot.

**1 = Stock CPU max Freq is 800 MHz and the maximum adjustable Freq of 1300 MHz is very rare to work stable, since it depends on the quality of the CPU.

However the minimum stable overclocking Freq should be 1150 MHz, but if your Phone has good Quality chips then it will work stable at 1200 MHz or even 1250 MHz.

So the very high Frequencies are not meant to work 100% stable, but they are there so that you can see what is the maximum stable Freq possible for your Phone.

**2 = Same like CPU, the Stock GPU max Freq is 400 MHz. The max adjustable Freq of 800 MHz is unlikely to work stable, but 650 - 700 MHz should work stable for every Phone.